Phones answered 24/7Atlanta, GA 30303
Call (833) 490-5225
(833) 490-5225
Guide

Mold After Water Damage in Georgia: No State Mold License, So What Should You Ask?

Georgia does not license mold remediators the way some states do. Learn what standard to ask a company to follow, what to expect in writing and what to avoid.

Illustration for the guide "Mold After Water Damage in Georgia: No State Mold License, So What Should You Ask?" (Atlanta, GA)
Short answer

Georgia does not license mold remediators the way some states do, so there is no state license to check. That makes the questions you ask the safeguard: which standard the company works to, such as IICRC S520, what it will document, how it contains the work and how it confirms the job is finished.

Key takeaways

  • Georgia does not license mold inspection or remediation the way some states do, so a company cannot be vetted by a state mold license and the buyer has to ask better questions.
  • IICRC S520 is the industry standard for professional mold remediation, and asking which standard a company follows and what it will put in writing is the most useful single test.
  • Mold needs moisture, and EPA guidance says that drying wet materials within 24 to 48 hours generally prevents mold from growing, which is why fast drying and documented readings matter most.
  • EPA's guide suggests homeowners can generally handle a small patch of about 10 square feet or less, while larger areas, sewage-contaminated materials or a damp HVAC system call for professional help.
  • Mold can trigger allergy and asthma symptoms in some people, so anyone sensitive should stay out of the work area, but no one can tell a mold's effects from its color.

Does Georgia license mold inspectors or remediators?

No. Georgia does not license mold inspection or remediation the way some states do, and there is no state mold license to ask a company for. Contractors who do repair work may need a general or residential contractor license, but that is a different thing from a mold credential.

Several industry sources say plainly that Georgia has no state license for mold inspection or remediation, and that the credentials clients and insurers look for are national, industry-issued ones. We could not open a Georgia statute on the point, so treat this as the consistent finding of secondary sources and not as a legal opinion. If it matters to a decision, ask the state board or an attorney.

What it means in practice is simple. A company advertising itself as a state-licensed mold remediator in Georgia is describing something the state does not issue, and a mold company that says it is certified owes you a clear answer about by whom. Anyone who says their technicians hold an industry credential should be able to say which one. A different thing entirely is the contractor license. Georgia generally requires a residential or general contractor license for residential work valued at $2,500 or more, which can cover the rebuilding after mold removal such as drywall, framing and flooring. You can check any contractor with the State Licensing Board for Residential and Commercial General Contractors, which sits under the Secretary of State.

Georgia's contractor rules have been changing in 2025 and 2026, and how the changes affect restoration firms is not settled. Do not rely on a summary, including this one, without checking the current position. And whether pure water mitigation counts as contracting work is also unresolved, so be wary of any company that gives you a confident yes or no.

If there is no license, what standard should a company follow?

Ask for ANSI/IICRC S520, the industry standard for professional mold remediation, published by the Institute of Inspection, Cleaning and Restoration Certification. IICRC is a non-government industry body, not a licensing agency. A company that works to S520 should be able to explain its containment, removal, cleaning and verification steps in plain terms.

Without a state license, a published standard is the nearest thing to a benchmark. S520 sets out how professional remediation is meant to be planned and carried out, and it works alongside S500, the companion standard for water damage restoration. IICRC also certifies individual technicians, so the useful question is not whether a company is certified but which certifications its technicians hold and whether the person coming to your house is one of them.

EPA guidance is the other reference. The EPA's guide to mold and moisture is written for homeowners and building managers, and it states the basic principle that governs everything else: mold growth is controlled by controlling moisture. Standards and guidance do not replace judgment, but they give you something concrete to hold a company against.

A fair way to run the conversation is to ask the same few questions of every company, listen to how specifically each one answers, and compare the answers. The table in the next section turns those into a checklist.

What should you ask a mold company, and what should the answers sound like?

Ask which standard it works to, who will do the work and what they hold, how it will contain the area, what will be removed and what cleaned, what it will document and how it will confirm the job is done. Specific answers in writing are a good sign, and vague reassurance or pressure is not.

The questions below are the most useful ones to ask. None of them requires technical knowledge, and a company that is used to working to a standard will usually answer them easily.

Questions to ask a mold company, what a good answer sounds like and what should worry you
QuestionA good answer sounds likeA warning sign
Which standard do you work to?Names ANSI/IICRC S520 and EPA guidance, and says what that means for this jobSays there is no standard, or says Georgia requires a license it does not
Who does the work and what do they hold?Names the credentials of the technicians, which you can verify with the issuing bodyClaims certification without saying whose, or will not say who is coming
How will you find the moisture source?Moisture readings and a plan to correct the cause before cleaningTreats mold as a surface problem and starts cleaning without readings
How will you contain the area?Describes barriers, negative air or HEPA filtration where it applies, and keeping spores out of the rest of the houseSays containment is unnecessary for any size job
What gets removed and what gets cleaned?Explains that porous wet materials are often removed, and that framing is cleaned and driedProposes to spray or paint over growth
How will we know it is finished?A written scope, drying readings and a verification step, such as a visual check or post-work testing as agreedPromises a result with no way to check it
Will I get it in writing?Scope, price and process on paper before work startsPressure to sign immediately

Why does the moisture matter more than the mold?

Mold needs moisture, so removing growth without fixing the water that fed it means it returns. EPA guidance says that wet materials dried within 24 to 48 hours generally do not grow mold. After that window, how long the material stayed wet matters most, and moisture readings show whether it is truly dry.

Mold spores are everywhere in indoor and outdoor air, and they only grow when they land on something damp that lasts. That is why drying is the first step in any water-damage job, not an extra. A crew uses moisture meters and thermal tools to find water that is not visible, sets air movers and dehumidifiers, and re-checks readings until materials are dry. If the readings are not documented, there is no proof the drying finished.

Atlanta's climate adds to the stakes. Summers are hot and humid, thunderstorms are frequent through the warm months and many older houses sit over damp crawl spaces, so the conditions that support mold are common for much of the year. A slow leak in August is a more serious mold risk than the same leak in January. Our guide to crawl space moisture on red clay explains how a damp space under a house can feed problems upstairs.

It also means the sequence matters. A typical order is to stop the water, dry the structure, then look at what mold is present and decide what to remove, clean or leave. Cleaning first and drying later is the wrong order. If you see mold, do not paint, caulk or seal over it, and do not run a fan over it, because disturbing growth can spread it through the house.

Can I clean the mold myself, and when should I not?

EPA guidance says a small area of about 10 square feet or less, roughly a 3 foot by 3 foot patch, can generally be handled by a homeowner. Larger areas, anything linked to sewage or flood water, or growth in an HVAC system generally call for professional help. Anyone sensitive should stay away from the work.

The 10-square-foot guideline comes from EPA's guide to mold and moisture in the home, and it is a rule of thumb for a small, clearly surface-level problem on a hard material, not a promise that everything below it is safe. On non-porous surfaces such as tile or glass, detergent and water and a thorough dry are the usual approach. Porous materials such as ceiling tile, carpet and drywall that have been wet for a long time often cannot be cleaned and are removed.

A few cases call for caution regardless of size:

  • Water that came from sewage or a drain backup, which is contaminated and a health hazard, not a cleaning job.
  • Flood water from a creek or a flooded yard, which can carry contamination.
  • Growth inside walls, under flooring or in the ductwork, where you cannot see how far it goes.
  • Anyone in the house with asthma, allergies, a weakened immune system or breathing problems.
  • Mold that returns after cleaning, which usually means the moisture source is still active.

Does mold testing help, and what about the color?

Color does not tell you what a mold is or how harmful it is, so no one can judge risk by looking. Testing can document what is in the air or on a surface, but EPA guidance says that sampling is not routinely necessary, and a visible problem and a moisture source matter more than a lab result.

People understandably worry about the most alarming-sounding mold, but color and appearance are not reliable. Mold can trigger allergy and asthma symptoms in some people, which is the practical concern, and the response is the same whatever the species: fix the moisture and remove or clean the affected materials. We make no health claims beyond that, and a doctor is the person to ask about symptoms.

Testing has a place when there is a reason for it, such as a hidden problem you cannot see, a dispute with a landlord or a buyer asking for documentation. A mold inspection and assessment typically costs about $250 to $650, an estimate drawn from the same range we use elsewhere and not an Atlanta price list. The better question is what the company will do with the result and whether the same company sells the testing and the removal, because that is a conflict of interest worth knowing about. Our mold inspection and moisture mapping page explains how moisture assessment fits in.

Be skeptical of any test result presented as a verdict. Air samples vary with the day, the weather and the sampling method, and the numbers mean little without a comparison such as an outdoor sample and an inspector who can explain them.

What does mold remediation cost, and what about asbestos and lead in older homes?

Typical estimates for small to mid-sized mold remediation in the Atlanta area run from about $500 to $6,000, confirmed on site. Older buildings add two checks: asbestos notification before demolition in larger buildings, and lead-safe rules for homes built before 1978. Ask before any wall or ceiling comes down.

The price depends on the area affected, how many materials must come out, how much containment the job needs and how long drying takes. Repairs after remediation, such as drywall, trim and flooring, are quoted separately, and drywall repair has been quoted at about $2.17 per square foot for Atlanta by one contractor-pricing site. These are typical estimates, not a market average, and not a price list. The price for the first stage is explained and approved before work starts.

Demolition brings two older-building questions. For asbestos, Georgia EPD's Lead-Based Paint and Asbestos Program takes notifications for renovation and demolition, and federal and Georgia rules generally require an inspection beforehand and written notice 10 working days ahead, except for residences of four or fewer dwelling units. Most Atlanta houses fall under that exemption, so the rule matters mainly in apartment blocks and commercial buildings. Check with Georgia EPD for your case.

For lead, homes built before 1978 fall under the EPA Renovation, Repair and Painting rule, which applies to contractors disturbing painted surfaces. Many intown houses were built before then, so ask the contractor how they handle it. Neither rule is a reason to delay drying. They are reasons to ask before demolition starts.

If you have mold and active water now, (833) 490-5225 is answered 24/7 and a crew is dispatched as fast as one is available. Our mold remediation page describes the work in more detail.

Frequently asked questions

Is there a state mold license in Georgia?

Georgia does not license mold inspectors or remediators the way some states do, based on several industry sources. Because we did not open a statute, check with the state or an attorney if it matters. Ask any company which standard it follows, such as IICRC S520, and what its technicians hold.

Does IICRC certification make a company licensed?

No. IICRC is an industry body, not a government licensing agency. It publishes standards such as S500 and S520 and certifies individual technicians. Ask which certifications a company's technicians hold and who will actually be at your house, and verify with the issuing body if it matters.

How soon does mold grow after water damage?

EPA guidance says that if wet materials are dried within 24 to 48 hours, mold generally will not grow. Beyond that window, growth becomes possible depending on the material and conditions. That is why drying quickly and documenting moisture readings matter more than any later cleaning step.

Should I paint or seal over small mold spots?

No. Paint and sealant do not fix the moisture that fed the mold, and growth can return and show through. Find and fix the moisture source, dry the area and clean or remove the affected material. If the area is larger than about 10 square feet, ask for professional help.

Will insurance cover mold?

It depends on the policy and the cause of the water. Many policies limit mold coverage, and mold that follows a long-term leak is commonly excluded. Your insurer decides under your policy, not a restoration company, so ask your agent before the work begins.

Sources

  1. U.S. EPA – A Brief Guide to Mold, Moisture, and Your Home
  2. IICRC – ANSI/IICRC S520 Standard for Professional Mold Remediation
  3. Georgia Secretary of State – Residential and Commercial General Contractors, Frequently Asked Questions
  4. Georgia EPD – Asbestos Notification Requirements

This guide is general information for Fulton County homeowners, not a substitute for an on-site inspection. Prices are estimates. See our disclaimer.

One call and it gets handled.

A crew is dispatched as fast as one is available, and you approve the estimate before any work starts.

Keep reading

More guides

WhatsApp